Miter Saw For Beginners: Buying Guide & How To Use It

What features does a miter saw for beginners need? If you are interested in this convenient woodworking equipment, do not ignore the information below.

One of the most accessible saws to make diagonal cuts and bevel cuts is the miter saw. Even beginners can get used to and perform cutting operations with a miter saw.

If you are looking for this simple tool or just found a cheap miter saw but don’t know how to use it, this article is for you who need to know how to choose and use a miter saw for beginners.

What Should I Look For In A Miter Saw For Beginners?

Miter Saw For Beginners

As an inexperienced person, you should not start with complex, multi-functional miter saws. Instead, it would help if you choose a miter saw that meets some of the following criteria:

Design And Material

Miter saw has many different designs: sliding miter saw, compound miter saw, compound sliding miter saw.

However, the most suitable option for beginners is the dual compound sliding saw. The type of design that includes the machine’s rails, rulers, and angles will facilitate you to cut both left and right.

In terms of materials, you should give preference to high-strength materials such as stainless steel. In addition, you also need to evaluate the robustness of the machine structure before making a decision.

Ease Of Use

Ease of use is one of the most important factors for beginners. You need to easily adjust the knob and read the scale with just one glance.

Therefore, the ideal miter saw should have the placement of buttons and screens as simple and accessible as possible.

It would help if you also chose miter saws that have preset modes. It may take some time to set up. However, a preset will bring you many benefits, especially when you do not have too much experience working with miter saws.

Cutting Capacity And Angles

If you are a beginner, the amount of work is not much; a saw with a 10-inch design is enough to get the job done. If you need to handle smaller materials and appreciate mobility, an 8-inch small saw will be the right choice.

Later, as you gain more work experience or frequently work with large materials, you may want to consider switching to a large 12-inch to 15-inch saw.

Dust Collection And Safety

Miter Saw For Beginners 1

As a beginner, you probably haven’t figured out what trouble you will have with dust. If you don’t know how to handle it properly, your space will be an actual mess and not safe to work in.

Do not let the dust from the saw block your view. A miter saw with a dust-proof port, and built-in controller will help you control the dust problem. From there, keep the working space clean and safe.

How To Use A Miter Saw 

It is not difficult to get used to and use a miter saw. By simply following a few guidelines, you’ll be able to handle materials quickly – safely with your miter saw.

Check if Your Miter Saw Cuts Straight

When first used, some types of circular saws cannot cut completely straight.

In order not to make mistakes when working, you cannot skip a quick check before use.

  • First, check the perpendicularity of the saw blade to the work plane.
  • The test operations are not too complicated: Unplug, then lift the blade guard. Prepare a square ruler or any square object. Then lower the blade, placing the square next to it.
  • If the saw blade is perpendicular to the table, you won’t see any gaps or light rays going through the two items above.
  • If the saw blade is not really vertical, you need to adjust the tilt of the bevel on the saw. Then don’t forget to reset the bevel gauge to zero.
  • Second, make sure the saw blade is perpendicular to the miter saw fence.
  • All you need to do is place the ruler perpendicular to one side against the edge, the other against the wall. Then adjust the bar until there are no gaps. Remember to tighten the bolts after adjusting.
  • Maybe after a period of use, your cuts will not be as accurate as they were initially. At this time, you need to repeat the above two checks and adjust the squareness of the blade.

How to Cut with a Miter Saw

Miter Saw For Beginners 2

Step 1: Measure the length of the board needed to process the material.

You need to prepare a tape measure, chalk or pencil. You will use chalk or pencil to draw a line on the board that you want to cut. Use a ruler to measure specific parameters and then mark the points that exceed the parameters.

Step 2: Align the board

At this step, you still must not turn on the saw. It would help to place the board over the saw so that the back edge rests against the fence.

Lower the saw blade and align it again. This alignment is the last because you always have to keep the board in place when you turn on the saw.

Step 3: Carry out sawing

  • Turn on the saw, but do not immediately process the material. You need to wait a few seconds for the blade to reach full speed. Then lower the edge slowly.

When the blade has ultimately passed through the board, release the trigger. All you need to do next is keep the edge in place when you lower it until it stops.

  • Don’t forget to wear protective gear when cutting. You should at least have safety glasses and ear protection to avoid any unnecessary damage.

FAQs

For you to better understand this type of machine, we answer some frequently asked questions below.

Is it safe to use a miter saw on the ground?

Miter Saw For Beginners 3

Using a miter saw on the ground has many potential safety risks. You may face back injuries and other dangers when moving into the workshop.

Besides, miter saw most require screwing. And obviously, you will have trouble with this step if you use the saw on the ground.

Why did my miter saw kickback?

Kickback occurs when the kerf is close to the blade. If you regularly handle long and wide boards, you will certainly be no stranger to this phenomenon.

As a workaround, some woodworkers will begin to process the material by cutting a portion near the fence side of the saw.

Why is my miter saw binding?

The cause of miter saw binding can come from an unsuitable blade or a rusted blade. To solve, you can adjust the edge.

In addition, in the cutting process, you do not follow the correct technique and will also cause the saw to be unable to cut the material.

Conclusion

Any woodworker, professional or amateur, has owned a miter saw. Probably because Miter saw for beginners has a simple, easy-to-use design. Or because miter saws are affordable but can handle a wide range of materials. Follow power tool blog at Geariz

Whatever the reason, it is a fact that you can complete your first projects with the help of a miter saw. The only thing you need to keep in mind is to choose the right saw for you so that using it will not be a problem.

Leave a Reply

Your email address will not be published. Required fields are marked *